oil quenching
英 [ɔɪl ˈkwentʃɪŋ]
美 [ɔɪl ˈkwentʃɪŋ]
油淬
双语例句
- Gears are often through-hardened by water or oil quenching in order to increase their resistance to wear.
齿轮通常都要经过在油介质或者水介质中旳整体淬火，以达到增加耐磨性的目的。 - This is not true in oil quenching, when the surface temperature may be high during the critical stages of quenching.
但油淬情况就不是如此，因为油淬时在淬火临界阶段零件表面的温度可能仍然很高。 - Adopting the cooling way of water quenching oil to perform the heat treatment quenching, to make the mechanical property of forgings meet the technical requirements.
热处理淬火采用水淬油冷的冷却方式，使模块锻件力学性能满足了技术要求。 - Mineral oil based quenching oil is not a green quenchant because it produces hazardous substance during service and wasted oil is difficult to be degraded.
矿物油基淬火油在使用中会产生有害物质，且废油难以降解，不属于绿色淬火介质。 - The harm of mineral oil based quenching oil to environment can be weakened through hydrogenation, improvement on addition component, and regeneration of wasted oil.
通过加氢处理、改进添加剂配方及废油再生可以减少矿物油基淬火油对环镜的危害。 - In order to improve the shock toughness of friction welding joint of oil drilling pipe, spray quenching is used as the measure of heat treatment after friction welding.
为研究锻件喷雾淬火冷却过程，研制了喷雾淬火热处理装置，并对轴类件进行喷雾淬火热处理试验。 - The distortion control of steels during vacuum oil quench and high pressure gas quenching is discussed.
讨论了钢真空油淬和高压气淬的变形控制问题，提出了在选择这两种工艺时应遵循的原则。 - However, it is imperative to develop, produce and apply vegetable oil based quenching oil and other green quenchants.
然而，开发、生产及使用植物油基淬火油等绿色淬火介质势在必行。 - The Research of Similarities and Differences about Die Performance after Vacuum Gas Quenching and Conventional Oil Quenching
快速加热冷却淬火法电流直接加热淬火法真空气淬和普通油淬对环模性能异同性的研究 - By plunging the hot metal into water, oil, or brine ( quenching), the desirable characteristics are retained.
将灼热金属插入水中或盐水（淬火），还会保持理想的特性。 - Comparing with traditional oil quenching, nitrate quenching has some advantages, including high quenching temperature, small deformation of the work pieces, safety and that the nitrate is not easy to aging and can be recovered.
硝盐淬火与传统油淬火相比有淬冷温度高，工件变形小、硝盐不易老化、安全性高，并可回收利用等特点。 - Study on Removal of Emulsifying Oil from Quenching Water with Amphiphilic Resins
用亲水亲油树脂处理急冷水乳化油废水的研究 - The results show that under the active of electric current pulse the lead bath quenching used commonly in the medium and high carbon wire rod steel can be completely replaced by the treatment technology of oil quenching and tempering.
结果表明；在脉冲电流的作用下，用油淬+回火的处理工艺完全可以取代中高碳盘条钢常用的铅浴淬火。 - Oil Quenching Technology for Light Hydrocarbons and Naphtha Cracking
轻烃、石脑油裂解的油急冷工艺 - Improving quenching quality of parts by replacing machine oil with special quenching oil
以专用淬火油取代机械油提高零件淬火质量 - A method for gathering and purifying the oil smoke which was produced by oil quenching tanks and tempering in the whole-sealed and constant-temperature heat treatment plant was introduced.
以一个全封闭恒温车间内热处理油烟的收集与净化为例，介绍了井式淬火油槽和井式回火炉中所产生油烟的收集与净化方法。 - Its applied result in bearing industry and others were presented, indicating that the overspeed quenching oil can greatly improve the hardness of quenching parts and the depth of quenching layer. It is a kind of cooling medium for quenching with good performance.
介绍了超速淬火油在轴承行业和其他行业的实际应用效果，证明超速淬火油可以显著地提高淬火零件的硬度和淬透层深度，是一种性能优良的淬火冷却介质。 - As for bright quenching oil, the directivity of oil flow is very significant in the quenching tank and its effective quenching zone is much narrower than water because its kinematic viscosity is much bigger than the latter.
光亮淬火油在淬火槽内的流动方向性非常强，它在淬火槽中的有效淬火区域比水的狭窄得多，这是因为光亮淬火油的运动粘度比水大得多。 - The study shows that, control of the optimal sintering time and use of oil quenching can change the boundary morphology of the wolfram carbide phase from edge form into smooth form, as a result the properties of the hard metal can be improved.
使用最佳烧结时间和采用油中淬火冷却方式，可以使原棱角形的碳化钨晶粒变为圆滑的晶粒，从而可以改善硬质合金的性能。 - After oil quenching from 1200 ℃, the microstructure consists of(α_2+ B2) phase. And the volume percentages of the two phases were nearly equal.
1200℃油淬样品的组织由α2+B2相组成，二相含量大致相近。 - The network YAG laser hardening on the surface of cylinder forms numerous micro oil pools with hardening skeleton constructed by laser quenching, which are favourable to the lubrication between cylinder and piston ring.
结果表明，采用YAG激光网纹状淬火可在汽缸表面形成众多的、以激光淬火形成骨架的微油池，它有利于活塞环与汽缸间的润滑。 - Study on Composite Treatment of Saucers in the Edible Oil Saucer Separator by Nitriding-Laser Quenching
食用油碟式分离机碟片的渗氮激光相变硬化复合处理研究 - Design of Inductor for Single-gear Tooth Submerged Oil Quenching
单齿埋油淬火感应器的设计 - Fire prevention for oil quenching
用油淬火的火灾防治 - Design and Application of Speed Change Equipment for Oil Quenching of Bar-parts in Well Furnace
变功率深井炉及其杆变速淬油装置的设计与应用